3D Blend Permanent Crown Resin (A0 Bleach, 500g)

Description

3D Blend Permanent Crown Resin is a ceramic-filled hybrid resin for durable, long-term restorations. The ceramic filler gives high stiffness, wear resistance and a natural, light-diffusing appearance.

It combines strength, a precise and stable fit, and biocompatible, low-odor chemistry — ideal for definitive crowns, inlays, onlays and veneers printed in-lab.

Key features

• Hybrid ceramic — ceramic-filled resin matrix
• High strength and wear resistance
• Precise fit and dimensional stability
• Natural aesthetics in VITA-style shades
• Biocompatible, low-odor formulation

Applications

• Single-unit crowns
• Inlays, onlays and veneers
• Long-term restorations

Product information

Item	Detail
Product	3D Blend Permanent Crown Resin
Type	Dental hybrid ceramic resin
Shade	A0 Bleach
Net weight	500 g
Wavelength	385–405 nm
Compatible printers	LCD, MSLA and DLP resin printers (Elegoo, Anycubic, Phrozen, Creality, Uniformation, Bambu and others)

Technical data

Property	Value
Ceramic filler content	40–70 wt% (typical for hybrid ceramic resins)
Flexural strength	100–150 MPa
Flexural modulus	4–7.5 GPa
Density	1.3–1.7 g/cm³

Typical values for this resin type, compiled from comparable resins — indicative only, not a guaranteed specification for this batch.

How to print

1. Bring resin and room to 20–30 °C — cold resin is thick and causes failed prints
2. Shake the bottle for 1–2 minutes (or roll it) until no sediment remains
3. Check the FEP/ACF film for holes and clean the build plate; level the plate if needed
4. Pour resin into the vat up to the MAX line
5. In your slicer (Chitubox, Lychee, etc.) enter the print settings below, orient parts at 30–45° and add supports
6. Hollow large models (2–3 mm wall) and add drain holes to save resin and avoid suction
7. Run an exposure test (e.g. RERF or validation matrix) the first time you use this resin on your printer
8. Print, then let the plate drip for 10–15 min before removing parts

Recommended print settings (UV exposure)

Setting	Starting value
Layer height	0.05 mm
Bottom layers	4–6
Lift distance	6 mm (8–10 mm on 7–10″ screens, 11–15 mm on 10–15″ screens)
Lift speed	60–80 mm/min
Retract speed	150 mm/min
Wavelength	385–410 nm
Bottom exposure	20–30 s
Layer exposure	3–5 s

Starting values tested on a 6.6″ mono LCD (3500–4500 µW/cm²). Adjust for your printer’s light power: a stronger screen needs shorter exposure; a weaker or ageing screen needs longer.

Washing

1. Clean in fresh IPA (95%+), ideally ultrasonic: 1–2 min first bath, 2–3 min second bath
2. Blow dry with an air gun immediately after washing
3. Finish and polish according to standard laboratory practice
4. Check fit on the model before clinical use

UV post-curing (polymerization)

Parameter	Value
Wavelength	405 nm
Dental curing unit (≈200 mW/cm²)	2 × 5 min (both sides), in glycerin or nitrogen if available
Standard curing station	Not recommended for definitive restorations — use a validated dental curing unit
Note	Full polymerization is essential for strength, color stability and biocompatibility

Tip: Filled resins settle: roll or shake the bottle thoroughly before every print and stir the vat between prints. Follow the post-cure protocol fully — strength depends on it.

Storage & safety

• Store sealed in the original bottle at 15–30 °C, away from sunlight, heat sources and moisture
• Shake or roll the bottle for 1–2 minutes before every print — pigments and fillers settle
• Shelf life: 24 months unopened (18 months for dental resins)
• Wear nitrile gloves and safety glasses; work in a ventilated room
• Skin contact: wash with soap and water. Eye contact: rinse 15 min and seek medical advice
• Dispose of uncured resin and contaminated IPA as chemical waste, never in the drain

For professional dental use only, by trained laboratory and clinical staff. Validate settings on your own printer and follow your local regulations for dental devices.

In the box

1 × 3D Blend Permanent Crown Resin (A0 Bleach), 500 g bottle.